SensorCatalog

Vacuum pressure converter

Convert vacuum pressures between Pa, mbar, Torr, mTorr and atm; 1 atm = 1013.25 mbar = 760 Torr.

1 mbar is 100 Pa, 0.75006 Torr and 750.06 mTorr; 1 atm is 1013.25 mbar or 760 Torr, and 1 Torr is 133.322 Pa (the Torr is defined as 1/760 atm).

Pressure

Result

100Pa

1 mbar

mbar
1100 Pa
Torr
0.750062133.322 Pa
mTorr
750.0620.133322 Pa
atm
0.000986923101325 Pa

Schematic

Pressure1 mbar100 Pa10³10⁰10⁻³10⁻⁶10⁻⁹mbar
Drawn from the inputs above; not to scale.
Formulas and standards
1 atm = 101 325 Pa = 1013.25 mbar = 760 Torr   1 Torr = 101 325/760 Pa

The vacuum units are defined exactly, not rounded: 1 atm = 101 325 Pa, 1 Torr = 101 325/760 Pa = 133.322368… Pa, 1 mbar = 100 Pa and 1 mTorr = 0.133322368… Pa. Vacuum datasheets mix mbar, Torr and Pa freely, so convert with the exact factors and round only at the end. Negative absolute pressures do not exist; a gauge that reads below the vapour pressure of the gas is measuring its own limit, not the chamber.

Typical ranges, for orientation only — each instrument states its own: Pirani and thermocouple gauges about 1e−3 to 1000 mbar; capacitance diaphragm gauges about 1e−5 to 1000 mbar (with the common industrial version covering 0.1 to 1000 mbar); hot-cathode ion gauges about 1e−10 to 1e−3 mbar; Bourdon-tube mechanical gauges about 1 to 1000 mbar. Always check the datasheet for the model and the gas.

Looking for vacuum gauges or pressure transmitters?

Contact us

Why vacuum units need care

A vacuum datasheet may quote mbar, Torr, Pa or atm for the same gauge. The conversions are exact, but they are not round numbers: 1 Torr is 133.322 Pa, and 1 mbar is 100 Pa, so 1 mbar is 0.750 Torr. Mixing the two by a few percent is the usual reason two instruments appear to disagree.

The definitions

  • 1 atm = 101 325 Pa = 1013.25 mbar = 760 Torr
  • 1 Torr = 101 325/760 Pa = 133.322368… Pa
  • 1 mbar = 100 Pa
  • 1 mTorr = 0.133322368… Pa

The Torr is defined from the atmosphere, not from the millimetre of mercury column, so the conversion is exact and reproducible. The calculator returns all four units from any one of them, with Pa as the reference.

Worked examples

  • 1 mbar = 100 Pa = 0.75006 Torr = 750.06 mTorr
  • 1 Torr = 133.322 Pa = 1.33322 mbar
  • 0.001 mbar = 1e−3 mbar = 0.750 mTorr = 0.1 Pa
  • 1 atm = 1013.25 mbar = 760 Torr

A rough scale helps: atmospheric pressure is about 1000 mbar, a rough vacuum pump reaches 1–10 mbar, a good two-stage rotary pump 1e−3 mbar, a turbomolecular pump 1e−7 mbar and an ion-pumped ultra-high vacuum 1e−10 mbar or below.

Gauge types and their ranges

  • Pirani and thermocouple gauges: about 1e−3 to 1000 mbar, gas-dependent at the low end.
  • Capacitance diaphragm gauges: about 1e−5 to 1000 mbar, with the common industrial version covering 0.1 to 1000 mbar.
  • Hot-cathode ion gauges: about 1e−10 to 1e−3 mbar, with a gas-species correction factor.
  • Bourdon-tube mechanical gauges: about 1 to 1000 mbar.

The ranges overlap so that a system can be covered by two instruments with a handover point. Check the datasheet for the exact model and the calibration gas: a Pirani gauge calibrated for nitrogen reads differently in helium or hydrogen.

Where the units meet

The same vacuum appears in other calculators: the pressure converter covers bar, psi, kPa and mmH₂O, and the dew-point calculator uses pressure dew point for compressed air, where the pressure is usually given in bar but the humidity in mbar of vapour pressure.

Common mistakes

Rounding the Torr factor. Using 133 Pa instead of 133.322 Pa is a 0.24 % error; at 1e−3 mbar it is small, at 760 Torr it is 245 Pa.

Mixing gauge and absolute pressure. A vacuum gauge may read absolute pressure or the difference from atmosphere; the datasheet says which one.

Assuming a gauge reads to zero. Every gauge has a lower limit set by its principle; below that the reading is noise.

Comparing readings in different units without converting. 1 mbar and 1 Torr differ by 25 %.

Frequently asked questions

How many Torr is 1 mbar?

0.75006 Torr. The exact factor is 100 × 760/101325.

Is 1 Torr exactly 1 mmHg?

Historically close, but the Torr is defined as 1/760 atm, while 1 mmHg depends on the density of mercury and gravity. They differ by about 1e−7 relative.

What is a rough vacuum in mbar?

Rough vacuum is usually taken as 1 to 1000 mbar, fine vacuum 1e−3 to 1 mbar and high vacuum below 1e−3 mbar; the boundaries vary by industry.

Can I convert a gauge reading below its range?

The unit conversion is still valid, but the number is outside the gauge’s specification. Below the range the reading is not a measurement.

↑ ↓ choose · Enter open · Esc close