SensorCatalog

Pipe velocity & diameter calculator

Flow velocity, the bore needed for a target velocity, and the Reynolds number for a pipe.

36 m³/h through a 50 mm bore is 5.093 m/s; at a target of 2 m/s the same flow needs a 79.8 mm bore, and the Reynolds number with water at 1 cSt is about 254 650 (turbulent).

Pipe

Result

5.093m/s

36 m³/h in 50 mm

Reynolds number
254600Flow regime
Bore for target
80 mmat 2 m/s
Flow area
0.0019635 m²π/4 · D²
Scope
mean velocity

Schematic

Internal diameter50 mmFlowv5.093 m/sRe254600Reynolds numberturbulent
Drawn from the inputs above; not to scale.
Formulas and standards
v = Q / (3600 · π/4 · D²)   D = √(4·Q / (3600·π·v))   Re = v·D/ν

The mean velocity is the volume flow divided by the flow area: v = Q/(3600·π/4·D²) with Q in m³/h and D in metres. Solving it for D gives the bore a target velocity needs. The Reynolds number Re = v·D/ν, with ν the kinematic viscosity in m²/s, tells whether the flow is laminar (below about 2300), transitional (2300–4000) or turbulent.

Velocity limits are project practice, not physics: suction lines are kept slow to protect NPSH, discharge lines faster to save pipe cost, and erosive or fouling services slower again. Typical water ranges are about 0.5–1.5 m/s on suction and 1.5–3 m/s on discharge, but the specification and the pump or instrument datasheet decide. Above about 3–4 m/s noise, erosion and pressure loss rise quickly; below about 0.5 m/s settling and fouling become likely.

Looking for flow meters or pipe instrumentation?

Contact us

Why pipe velocity matters

The mean velocity is the flow divided by the pipe’s flow area. It sets the pressure loss, the noise, the erosion rate and, on a suction line, the risk of cavitation. A line that looks conservative on a drawing can still be wrong if the velocity is far outside the range the pump or the instrument expects. The calculator returns the velocity for a given flow and bore, the bore needed for a chosen velocity, and the Reynolds number that says whether the flow is laminar or turbulent.

The equations

  • v = Q / (3600 · π/4 · D²)
  • D = √(4·Q / (3600·π·v))
  • Re = v·D / ν

Q is in m³/h, D in metres and ν in m²/s (1 cSt = 1e−6 m²/s). The velocity is the mean over the cross-section; the profile is faster in the centre and zero at the wall.

Worked example

36 m³/h through a 50 mm bore:

  • area = π/4 × 0.05² = 0.0019635 m²
  • v = 0.01 m³/s / 0.0019635 = 5.093 m/s
  • with water at ν = 1 cSt, Re = 5.093 × 0.05 / 1e−6 = 254 650, turbulent

For a target of 2 m/s the same flow needs a 79.8 mm bore, which in practice means a DN 80 pipe. That is the usual selection step: compute the bore, round up to the next commercial size, then recheck the velocity and the pressure loss.

Choosing a velocity

Velocity limits are project practice, not physics:

  • Suction lines: about 0.5–1.5 m/s for water, slower where NPSH margin is tight.
  • Discharge lines: about 1.5–3 m/s for water, faster for clean fluids where pressure loss is cheap.
  • Erosive or fouling services: slower again, and above 3–4 m/s noise and erosion rise quickly.
  • Gas lines: much higher velocities are normal, but the pressure loss and noise limits still apply.

The pump datasheet, the instrument’s required straight run and the plant specification override any general table. The pump power calculator shows how the head and power respond to the duty, and the flow rate converter changes Q between units.

Pressure loss is the next check

Velocity is only half of the design: the pressure loss follows from the velocity, the length, the fittings and the roughness. Use the Darcy–Weisbach relation with the friction factor from the Reynolds number, or the pipe chart the supplier provides, and keep the total loss inside the pump’s available head. A line that meets a velocity target can still exceed the available head if it is long or has many bends.

Common mistakes

Using the outside diameter. The velocity is based on the internal bore, which is smaller by twice the wall thickness and can be much smaller in an old or scaled pipe.

Ignoring viscosity. The Reynolds number and the pressure loss change completely between water and oil; the velocity alone does not describe the flow.

Choosing the bore from velocity only. Pressure loss, available head and NPSH decide as well; the velocity is a check, not the whole design.

Forgetting that velocity changes with flow. A line sized for the design flow runs slow at low load and fast at the maximum; check both ends of the range.

Frequently asked questions

What is a good water velocity in a pipe?

Typically 1.5–3 m/s on discharge and 0.5–1.5 m/s on suction, but the plant specification and the equipment datasheets decide.

How do I size a pipe for a flow?

Choose a target velocity, compute D = √(4Q/(3600πv)), round up to the next commercial bore and recheck the velocity and pressure loss.

What Reynolds number is turbulent?

Above about 4000 the flow is turbulent; below about 2300 it is laminar; between them it is transitional.

Does the pipe material matter?

For the velocity, no; for the pressure loss and erosion, yes — roughness and hardness matter.

Can I use the calculator for gas?

The velocity and Reynolds number relations hold for any fluid; the viscosity and the allowed velocity range change, and gas lines usually run much faster.

↑ ↓ choose · Enter open · Esc close