SensorCatalog

Heat load calculator

Sensible heat load from flow, density, specific heat and temperature difference.

1 m³/h of water heated by 10 K needs 11.63 kW (1000 × 1 × 4.186 × 10 / 3600); the same volume flow of air needs only 0.00335 kW because its density and specific heat are far lower.

Duty

Result

11.628kW

1 m³/h · ΔT 10 K

In kcal/h
9999.9 kcal/h1 kW = 860 kcal/h
In MJ/h
41.86 MJ/h1 kW = 3.6 MJ/h
Medium
1000 kg/m³cp 4.186 kJ/(kg·K)
Scope
sensible heat

Schematic

Temperature difference10 KP11.628 kWFlow1 m³/hT + ΔT
Drawn from the inputs above; not to scale.
Formulas and standards
P = ρ · Q · cp · ΔT / 3600   (kW)

The heat load is the mass flow times the specific heat times the temperature change: P = ρ·Q·cp·ΔT/3600, with Q in m³/h, ρ in kg/m³ and cp in kJ/(kg·K). Water is about 1000 kg/m³ and 4.186 kJ/(kg·K); air at room temperature is about 1.2 kg/m³ and 1.005 kJ/(kg·K). A negative ΔT gives a cooling load.

This is sensible heat only: it does not include latent heat (condensation or evaporation), heat of reaction, or losses. For a heater or a chiller selection, add the margins the application needs and use the medium data at the working temperature; cp and ρ both change with temperature. 1 kW is 860 kcal/h or 3.6 MJ/h.

Looking for temperature sensors or flow meters for heat metering?

Contact us

What the heat load is

The heat load is the rate at which heat must be added to, or removed from, a flowing medium to change its temperature. It is the first number in sizing a heater, a chiller, a heat exchanger or a control valve for a temperature loop.

The equation

  • P = ρ · Q · cp · ΔT / 3600 kW

Q is the volume flow in m³/h, ρ the density in kg/m³, cp the specific heat in kJ/(kg·K) and ΔT the temperature change in kelvin (the same number as °C). The 3600 converts hours to seconds and kJ/s to kW.

Worked example

1 m³/h of water, heated from 10 °C to 20 °C:

  • P = 1000 × 1 × 4.186 × 10 / 3600 = 11.63 kW
  • in other units: 11.63 kW = 10 000 kcal/h = 41.9 MJ/h

The same 1 m³/h of air at room temperature (ρ ≈ 1.2, cp ≈ 1.005) needs only 0.00335 kW, about 3.35 W, because there is very little mass in a cubic metre of air. That is why air heating is usually sized on mass flow or on the air handler’s duty, not on a water-style volume flow.

Sensible and latent heat

The equation covers sensible heat, the temperature change of a medium that does not change phase. Condensation, evaporation and chemical reaction add latent heat: water’s latent heat of vaporisation is about 2257 kJ/kg at 100 °C, so condensing 1 kg/h of steam releases about 0.63 kW. A steam heater needs the latent term; a water heater usually does not.

Where it is used

  • Heater and chiller selection: the kW at the design flow and ΔT.
  • Heat meters: the same product, integrated over time, gives kWh.
  • Temperature control: the load sets the valve or heater capacity and the loop’s response time.
  • Tank heating: the tank volume calculator gives the inventory, and the pipe velocity calculator checks the flow that carries the heat.

Common mistakes

Using the volume flow of a gas as if it were water. The density difference is a factor of about 800.

Forgetting the 3600. A result a thousand times too large is the usual symptom.

Using cp at the wrong temperature. cp changes with temperature, especially near a phase change.

Ignoring losses. The duty at the medium is not the duty at the heater terminals; insulation and pipe losses add.

Frequently asked questions

Is heat load the same as power?

For a steady flow with a known ΔT, yes: the heat load is the power the heater or chiller must deliver.

What is the unit?

kW is standard; 1 kW = 860 kcal/h = 3.6 MJ/h = 3412 BTU/h.

Can I use it for cooling?

Yes, with a negative ΔT; the magnitude is the cooling load.

Does it include the heat to warm the tank itself?

No. Warming the steel, the insulation and the pipe is a separate term that decays after start-up; add it for batch heating.

Why is air’s load so small?

Because its density and specific heat are low: a cubic metre of air carries about 1/800 of the heat of a cubic metre of water for the same ΔT.

↑ ↓ choose · Enter open · Esc close