SensorCatalog

Orifice / differential-pressure flow calculator

Flow through an orifice plate from Δp, bore, pipe diameter, density and the discharge coefficient.

With D = 100 mm, d = 60 mm, Δp = 25 kPa, ρ = 1000 kg/m³, C = 0.61 and ε = 1 the orifice equation gives about 47.06 m³/h; C and ε come from ISO 5167-2 and the gas data, not from this page.

Orifice and pipe

Coefficients

C and ε are not calculated here: take them from ISO 5167-2 (Reader–Harris/Gallagher) or the maker, with ε = 1 for liquids.

Result

47.06m³/h

C 0.61 · ε 1

Diameter ratio β
0.6β = d/D, ISO range 0.1–0.75
Orifice area
2827 mm²0.002827433 m²
Pipe velocity
1.664 m/smean velocity upstream
Scope
C and ε supplied

Schematic

Δp25 kPaQ47.06 m³/hD100 mmOrifice bore60 mmβ0.6
Drawn from the inputs above; not to scale.
Formulas and standards
Q = C · ε · A₂ / √(1 − β⁴) · √(2·Δp / ρ)

The orifice equation is Q = C·ε·A₂/√(1−β⁴)·√(2Δp/ρ), with A₂ the bore area, β = d/D and Δp in Pa. For a liquid ε = 1; for a gas it comes from the isentropic exponent and the pressure ratio. The discharge coefficient C for an ISO 5167-2 orifice comes from the Reader–Harris/Gallagher equation and depends on β and the pipe Reynolds number, which is why this page takes C as an input rather than guessing it.

The equation is exact for the numbers entered, but a standard-compliant orifice sizing also needs the Reynolds number, the tap arrangement, the roughness and the installation conditions of ISO 5167-2. Use the maker’s sizing program or the standard for a custody or safety-related measurement; use this page to check a reading, compare taps or understand the sensitivity before that.

Looking for orifice plates or differential-pressure transmitters?

Contact us

What the orifice equation gives

An orifice plate creates a pressure difference that grows with the square of the flow. The ISO 5167 equation turns a measured Δp into a volume flow:

  • Q = C · ε · A₂ / √(1 − β⁴) · √(2·Δp / ρ)

A₂ is the bore area, β = d/D, C is the discharge coefficient and ε the expansibility factor. This page computes Q from those inputs; it does not calculate C or ε, because both depend on details the standard defines.

The inputs

  • Pipe internal diameter D and orifice bore d, in millimetres; β = d/D must lie in the ISO range 0.1–0.75.
  • Differential pressure Δp in kPa, measured across the taps.
  • Density ρ at upstream conditions, in kg/m³.
  • Discharge coefficient C, from ISO 5167-2 or the maker.
  • Expansibility ε: exactly 1 for a liquid; for a gas, from the isentropic exponent and the pressure ratio.

Worked example

D = 100 mm, d = 60 mm, Δp = 25 kPa, water at 1000 kg/m³, C = 0.61, ε = 1:

  • β = 0.6, A₂ = 0.0028274 m²
  • 1/√(1 − 0.6⁴) = 1.07187
  • Q = 0.61 × 1.07187 × 0.0028274 × √50 = 0.013072 m³/s = 47.06 m³/h

The pipe velocity follows from the same flow and the pipe area: 1.67 m/s.

Where C comes from

For an ISO 5167-2 orifice with flange taps, C is the Reader–Harris/Gallagher correlation: it depends on β, the pipe Reynolds number, the tap positions and the pipe roughness, and it lands between about 0.596 and 0.62 inside the standard’s limits. That is why a coefficient typed into a calculator is only as good as its source. Take C from the standard’s equation, from the maker’s sizing sheet, or from a calibrated baseline; do not assume 0.61 for every plate.

Limits of the standard

ISO 5167-2 applies to a defined geometry: a thin square-edged orifice, specified tap arrangements, a straight run upstream and downstream, β 0.1–0.75, D 50–1000 mm and a Reynolds number above about 5000. Outside those limits the uncertainty grows and the equation is no longer a standard measurement. A custody transfer or safety trip needs the standard’s full procedure, not a single equation. The flow rate converter and pressure converter help with the units around the measurement.

Common mistakes

Using gauge pressure instead of Δp. The equation needs the difference across the plate, in Pa.

Taking C = 0.61 blindly. The coefficient moves with β and Reynolds number; a few percent of error in C is a few percent of flow.

Forgetting the expansibility for gas. ε below 1 reduces the flow; using 1 for a gas over-reads.

Ignoring the installation. A valve or bend too close to the plate changes the profile and the coefficient.

Frequently asked questions

Is this a full ISO 5167 sizing?

No. It is the ISO 5167 flow equation with C and ε supplied by you; a compliant sizing also needs the coefficient correlation, the Reynolds number and the installation checks.

What is a typical discharge coefficient?

About 0.60–0.62 for a standard square-edged orifice inside the ISO limits, but take the value from the standard or the maker.

What is ε for water?

Exactly 1. Liquids are incompressible for this equation.

Why does flow follow the square root of Δp?

Because the pressure difference is proportional to the dynamic pressure, which goes with the square of velocity.

Can I use it for a Venturi or a nozzle?

The same equation form applies with the device’s own C and ε; the coefficients differ.

↑ ↓ choose · Enter open · Esc close